Occupational Safety and Health Standards: Personal Protective Equipment, Eye and face protection.

If you are the victim of construction accidents, use this page to conduct research. To have your case evaluated immediately, please fill out our form. Read more about the Occupational Safety and Health Standards, 1910.133, Personal Protective Equipment, Eye and face protection..

1910.133(a)

General requirements.

1910.133(a)(1)

The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation.

1910.133(a)(2)

The employer shall ensure that each affected employee uses eye protection that provides side protection when there is a hazard from flying objects. Detachable side protectors (e.g. clip-on or slide-on side shields) meeting the pertinent requirements of this section are acceptable.

1910.133(a)(3)

The employer shall ensure that each affected employee who wears prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design, or wears eye protection that can be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lenses.

1910.133(a)(4)

Eye and face PPE shall be distinctly marked to facilitate identification of the manufacturer.

..1910.133(a)(5)

1910.133(a)(5)

The employer shall ensure that each affected employee uses equipment with filter lenses that have a shade number appropriate for the work being performed for protection from injurious light radiation. The following is a listing of appropriate shade numbers for various operations.

Filter Lenses for Protection Against Radiant Energy

____________________________________________________________________

Minimum(*)

Operations Electrode Size 1/32 in. Arc Current Protective

Shade

_____________________________________________________________________

Shielded metal

arc welding Less than 3 ......... Less than 60 ... 7

3-5 ................. 60-160 ......... 8

5-8 ................. 160-250 ........ 10

More than 8 ......... 250-550 ........ 11

_____________________________________________________________________

Gas metal arc

welding and

flux cored

arc welding less than 60 ... 7

60-160 ......... 10

160-250 ........ 10

250-500 ........ 10

_____________________________________________________________________

Gas Tungsten

arc welding less than 50 ... 8

50-150 ......... 8

150-500 ........ 10

_____________________________________________________________________

Air carbon (Light) ............. less than 500 .. 10

Arc cutting (Heavy) ............. 500-1000 ....... 11

_____________________________________________________________________

Plasma arc welding less than 20 ... 6

20-100 ......... 8

100-400 ........ 10

400-800 ........ 11

_____________________________________________________________________

Plasma arc (light)(**) ......... less than 300 .. 8

cutting (medium)(**) ........ 300-400 ........ 9

(heavy)(**) ......... 400-800 ........ 10

_____________________________________________________________________

Torch brazing ................ 3

Torch soldering ................ 2

Carbon arc welding ................ 14

_____________________________________________________________________

Filter Lenses for Protection Against Radiant Energy

_____________________________________________________________________

Minimum(*)

Operations Plate thickness-inches Plate thickness-mm Protective

Shade

_____________________________________________________________________

Gas Welding:

Light Under 1/8 ............ Under 3.2 ......... 4

Medium 1/8 to 1/2 ........... 3.2 to 12.7 ....... 5

Heavy Over 1/2 ............. Over 12.7 ......... 6

_____________________________________________________________________

Oxygen cutting:

Light Under 1 .............. Under 25 .......... 3

Medium 1 to 6 ............... 25 to 150 ......... 4

Heavy Over 6 ............... Over 150 .......... 5

______________________________________________________________________

Footnote(*) As a rule of thumb, start with a shade that is too dark

to see the weld zone. Then go to a lighter shade which gives

sufficient view of the weld zone without going below the minimum. In

oxyfuel gas welding or cutting where the torch produces a high yellow

light, it is desirable to use a filter lens that absorbs the yellow

or sodium line in the visible light of the (spectrum) operation.

Footnote(**) These values apply where the actual arc is clearly

seen. Experience has shown that lighter filters may be used when the

arc is hidden by the workpiece.

1910.133(b)

Criteria for protective eye and face devices.

1910.133(b)(1)

Protective eye and face devices purchased after July 5, 1994 shall comply with ANSI Z87.1-1989, "American National Standard Practice for Occupational and Educational Eye and Face Protection," which is incorporated by reference as specified in Sec. 1910.6.

1910.133(b)(2)

Eye and face protective devices purchased before July 5, 1994 shall comply with the ANSI "USA standard for Occupational and Educational Eye and Face Protection," Z87.1-1968, which is incorporated by reference as specified in Sec. 1910.6, or shall be demonstrated by the employer to be equally effective.

[59 FR 16360, April 6, 1994; 59 FR 33910, July 1, 1994; 61 FR 9227, March 7, 1996; 61 FR 19547, May 2, 1996]

Act now! It is essential that you inquire about your case as soon as possible. Litigation may be the only way to receive the damages to which you may be entitled, such as medical and health care bills, lost or diminished wages, and financial compensation to family in the case of death. Your individual state's law may limit your time to bring a legal claim to protect your rights. You need to have your construction accidents claim evaluated immediately!

Click To Talk To Us Online

see also:

General requirements FREE construction accidents OSHA information: General requirements.
construction accidents info: Personal Protective Equipment, General requirements.

Head protection FREE construction accidents OSHA information: Head protection.
construction accidents info: Personal Protective Equipment, Head protection.

Authority for 1910 Subpart I FREE construction accidents OSHA information: Authority for 1910 Subpart I
construction accidents info: Personal Protective Equipment, Authority for 1910 Subpart I