Occupational Safety and Health Standards: Machinery and Machine Guarding, Mills and calenders in the rubber and plastics industries.

If you are the victim of construction accidents, use this page to conduct research. To have your case evaluated immediately, please fill out our form. Read more about the Occupational Safety and Health Standards, 1910.216, Machinery and Machine Guarding, Mills and calenders in the rubber and plastics industries..

1910.216(a)

General requirements -

1910.216(a)(1)

[Reserved]

1910.216(a)(2)

[Reserved]

1910.216(a)(3)

Auxiliary equipment. Mechanical and electrical equipment and auxiliaries shall be installed in accordance with this section and Subpart S of this part.

1910.216(a)(4)

Mill roll heights. All new mill installations shall be installed so that the top of the operating rolls is not less than 50 inches above the level on which the operator stands, irrespective of the size of the mill. This distance shall apply to the actual working level, whether it be at the general floor level, in a pit, or on a platform.

1910.216(b)

Mill safety controls -

1910.216(b)(1)

Safety trip control. A safety trip control shall be provided in front and in back of each mill. It shall be accessible and shall operate readily on contact. The safety trip control shall be one of the following types or a combination thereof:

..1910.216(b)(1)(i)

1910.216(b)(1)(i)

Pressure-sensitive body bars. Installed at front and back of each mill having a 46-inch roll height or over. These bars shall operate readily by pressure of the mill operator's body.

1910.216(b)(1)(ii)

Safety triprod. Installed in the front and in the back of each mill and located within 2 inches of a vertical plane tangent to the front and rear rolls. The top rods shall be not more than 72 inches above the level on which the operator stands. The triprods shall be accessible and shall operate readily whether the rods are pushed or pulled.

1910.216(b)(1)(iii)

Safety tripwire cable or wire center cord. Installed in the front and in the back of each mill and located within 2 inches of a vertical plane tangent to the front and rear rolls. The cables shall not be more than 72 inches above the level on which the operator stands. The tripwire cable or wire center cord shall operate readily whether cable or cord is pushed or pulled.

1910.216(b)(2)

[Reserved]

1910.216(b)(3)

Auxiliary equipment. All auxiliary equipment such as mill divider, support bars, spray pipes, feed conveyors, strip knives, etc., shall be located in such a manner as to avoid interference with access to and operation of safety devices.

..1910.216(c)

1910.216(c)

Calender safety controls -

1910.216(c)(1)

Safety trip, face. A safety triprod, cable, or wire center cord shall be provided across each pair of in-running rolls extending the length of the face of the rolls. It shall be readily accessible and operate whether pushed or pulled. The safety tripping devices shall be located within reach of the operator and the bite.

1910.216(c)(2)

Safety trip, side. On both sides of the calender and near each end of the face of the roll, there shall be a cable or wire center cord connected to the safety trip. They shall operate readily when pushed or pulled.

1910.216(d)

Protection by location -

1910.216(d)(1)

Mills. Where a mill is so installed that persons cannot normally reach through, over, under, or around to come in contact with the roll bite or be caught between a roll and an adjacent object, then, provided such elements are made a fixed part of a mill, safety control devices listed in paragraph (b) of this section shall not apply.

1910.216(d)(2)

Calenders. Where a calender is so installed that persons cannot normally reach through, over, under, or around to come in contact with the roll bite or be caught between a roll and an adjacent object, then, provided such elements are made a fixed part of a calender, safety control devices listed in paragraph (c) of this section shall not apply.

..1910.216(e)

1910.216(e)

Trip and emergency switches. All trip and emergency switches shall not be of the automatically resetting type, but shall require manual resetting.

1910.216(f)

Stopping limits -

1910.216(f)(1)

Determination of distance of travel. All measurements on mills and calenders shall be taken with the rolls running empty at maximum operating speed. Stopping distances shall be expressed in inches of surface travel of the roll from the instant the emergency stopping device is actuated.

1910.216(f)(2)

Stopping limits for mills. All mills irrespective of the size of the rolls or their arrangement (individually or group-driven) shall be stopped within a distance, as measured in inches of surface travel, not greater than 1 1/2 percent of the peripheral no-load surface speeds of the respective rolls as determined in feet per minute.

1910.216(f)(3)

Stopping limits for calenders.

1910.216(f)(3)(i)

All calenders, irrespective of size of the rolls or their configuration, shall be stopped within a distance, as measured in inches of surface travel, not greater than 1 3/4 percent of the peripheral no-load surface speeds of the respective calender rolls as determined in feet per minute.

1910.216(f)(3)(ii)

Where speeds above 250 feet per minute as measured on the surface of the drive roll are used, stopping distances of more than 1 3/4 percent are permissible. Such stopping distances shall be subject to engineering determination.

[39 FR 23502, June 27, 1974, as amended at 49 FR 5323, Feb. 10, 1984; 61 FR 9227, March 7, 1996]

Act now! It is essential that you inquire about your case as soon as possible. Litigation may be the only way to receive the damages to which you may be entitled, such as medical and health care bills, lost or diminished wages, and financial compensation to family in the case of death. Your individual state's law may limit your time to bring a legal claim to protect your rights. You need to have your construction accidents claim evaluated immediately!

Click To Talk To Us Online

see also:

Definitions FREE construction accidents OSHA information: Definitions.
construction accidents info: Machinery and Machine Guarding, Definitions.

Mechanical power presses FREE construction accidents OSHA information: Mechanical power presses.
construction accidents info: Machinery and Machine Guarding, Mechanical power presses.

Authority for 1910 Subpart O FREE construction accidents OSHA information: Authority for 1910 Subpart O
construction accidents info: Machinery and Machine Guarding, Authority for 1910 Subpart O