Occupational Safety and Health Standards: General, Incorporation by reference.

If you are the victim of construction accidents, use this page to conduct research. To have your case evaluated immediately, please fill out our form. Read more about the Occupational Safety and Health Standards, 1910.6, General, Incorporation by reference.

1910.6(a)

1910.6(a)(1)

The standards of agencies of the U.S. Government, and organizations which are not agencies of the U.S. Government which are incorporated by reference in this part, have the same force and effect as other standards in this part. Only the mandatory provisions (i.e., provisions containing the word "shall" or other mandatory language) of standards incorporated by reference are adopted as standards under the Occupational Safety and Health Act.

1910.6(a)(2)

Any changes in the standards incorporated by reference in this part and an official historic file of such changes are available for inspection at the national office of the Occupational Safety and Health Administration, U.S. Department of Labor, Washington, DC 20210.

1910.6(a)(3)

The materials listed in paragraphs (b) through (w) of this section are incorporated by reference in the corresponding sections noted as they exist on the date of the approval, and a notice of any change in these materials will be published in the Federal Register. These incorporations by reference were approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.

..1910.6(a)(4)

1910.6(a)(4)

Copies of the following standards that are issued by the respective private standards organizations may be obtained from the issuing organizations. The materials are available for purchase at the corresponding addresses of the private standards organizations noted below. In addition, all are available for inspection at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington DC, and through the OSHA Docket Office, room N2625, U.S. Department of Labor, 200 Constitution Ave., Washington, DC 20210, or any of its regional offices.

1910.6(b)

The following material is available for purchase from the American Conference of Governmental Industrial Hygienists (ACGIH), 1014 Broadway, Cincinnati OH 45202:

1910.6(b)(1)

"Industrial Ventilation: A Manual of Recommended Practice" (22nd ed., 1995), incorporation by reference (IBR) approved for 1910.124(b)(4)(iii).

1910.6(b)(2)

Threshold Limit Values and Biological Exposure Indices for 1986-87 (1986), IBR approved for 1910.120, PEL definition.

1910.6(c)

The following material is available for purchase from the American Society of Agricultural Engineers (ASAE), 2950 Niles Road, Post Office Box 229, St. Joseph, MI 49085:

1910.6(c)(1)

ASAE Emblem for Identifying Slow Moving Vehicles, ASAE S276.2 (1968), IBR approved for 1910.145(d)(10).

1910.6(c)(2)

[Reserved]

1910.6(d)

The following material is available for purchase from the Agriculture Ammonia Institute-Rubber Manufacturers (AAI-RMA) Association, 1400 K St. NW, Washington DC 20005:

..1910.6(d)(1)

1910.6(d)(1)

AAI-RMA Specifications for Anhydrous Ammonia Hose, IBR approved for 1910.111(b)(8)(i).

1910.6(d)(2)

[Reserved]

1910.6(e)

The following material is available for purchase from the American National Standards Institute (ANSI), 11 West 42nd St., New York, NY 10036:

1910.6(e)(1)

ANSI A10.2-44 Safety Code for Building Construction, IBR approved for 1910.144(a)(1)(ii).

1910.6(e)(2)

ANSI A10.3-70 Safety Requirements for Explosive-Actuated Fastening Tools, IBR approved for 1910.243(d)(1)(i).

1910.6(e)(3)

ANSI A11.1-65 (R 70) Practice for Industrial Lighting, IBR approved for 1910.219(c)(5)(iii); 1910.261(a)(3)(i), (c)(10), and (k)(21); and 1910.265(c)(2).

1910.6(e)(4)

ANSI A11.1-65 Practice for Industrial Lighting, IBR approved for 1910.262(c)(6) and 1910.265(d)(2)(i)(a).

..1910.6(e)(5)

1910.6(e)(5)

ANSI A12.1-67 Safety Requirements for Floor and Wall Openings, Railings, and Toe Boards, IBR approved for 1910.66 Appendix D, (c)(4); 1910.68(b)(4) and (b)(8)(ii); 1910.261(a)(3)(ii), (b)(3), (c)(3)(i), (c)(15)(ii), (e)(4), (g)(13), (h)(1), (h)(3)(vi), (j)(4)(ii) and (iv), (j)(5)(i), (k)(6), (k)(13)(i), and (k)(15).

1910.6(e)(6)

ANSI A13.1-56 Scheme for the Identification of Piping Systems, IBR approved for 1910.253(d)(4)(ii); 1910.261(a)(3)(iii); 1910.262(c)(7).

1910.6(e)(7)

ANSI A14.1-68 Safety Code for Portable Wood Ladders, Supplemented by ANSI A14.1a-77, IBR approved for 1910.261(a)(3)(iv) and (c)(3)(i).

1910.6(e)(8)

ANSI A14.2-56 Safety Code for Portable Metal Ladders, Supplemented by ANSI A14.2a-77, IBR approved for 1910.261(a)(3)(v) and (c)(3)(i).

1910.6(e)(9)

ANSI A14.3-56 Safety Code for Fixed Ladders, IBR approved for 1910.68(b)(4) and (12); 1910.179(c)(2); and 1910.261(a)(3)(vi) and (c)(3)(i).

1910.6(e)(10)

ANSI A17.1-65 Safety Code for Elevators, Dumbwaiters and Moving Walks, Including Supplements, A17.1a (1967); A17.1b (1968); A17.1c (1969); A17.1d (1970), IBR approved for 1910.261(a)(3)(vii), (g)(11)(i), and (l)(4).

..1910.6(e)(11)

1910.6(e)(11)

ANSI A17.2-60 Practice for the Inspection of Elevators, Including Supplements, A17.2a (1965), A17.2b (1967), IBR approved for 1910.261(a)(3)(viii).

1910.6(e)(12)

ANSI A90.1-69 Safety Standard for Manlifts, IBR approved for 1910.68(b)(3).

1910.6(e)(13)

ANSI A92.2-69 Standard for Vehicle Mounted Elevating and Rotating Work Platforms, IBR approved for 1910.67(b)(1), (2), (c)(3), and (4) and 1910.268(s)(1)(v).

1910.6(e)(14)

ANSI A120.1-70 Safety Code for Powered Platforms for Exterior Building Maintenance, IBR approved for 1910.66 App. D(b) through (d).

1910.6(e)(15)

ANSI B7.1-70 Safety Code for the Use, Care and Protection of Abrasive Wheels, IBR approved for 1910.94(b)(5)(i)(a); 1910.215(b)(12); and 1910.218(j)(5).

1910.6(e)(16)

ANSI B15.1-53 (R 58) Safety Code for Mechanical Power Transmission Apparatus, IBR approved for 1910.68(b)(4) and 1910.261(a)(3)(ix), (b)(1), (e)(3), (e)(9), (f)(4), (j)(5)(iv), (k)(12), and (l)(3).

..1910.6(e)(17)

1910.6(e)(17)

ANSI B20.1-57 Safety Code for Conveyors, Cableways, and Related Equipment, IBR approved for 1910.218(j)(3); 1910.261 (a)(3)(x), (b)(1), (c)(15)(iv), (f)(4), and (j)(2); 1910.265(c)(18)(i).

1910.6(e)(18)

ANSI B30.2-43 (R 52) Safety Code for Cranes, Derricks, and Hoists, IBR approved for 1910.261(a)(3)(xi), (c)(2)(vi), and (c)(8)(i) and (iv).

1910.6(e)(19)

ANSI B30.2.0-67 Safety Code for Overhead and Gantry Cranes, IBR approved for 1910.179(b)(2); 1910.261(a)(3)(xii), (c)(2)(v), and (c)(8)(i) and (iv).

1910.6(e)(20)

ANSI B30.5-68 Safety Code for Crawler, Locomotive, and Truck Cranes, IBR approved for 1910.180(b)(2) and 1910.261(a)(3)(xiii).

1910.6(e)(21)

ANSI B30.6-69 Safety Code for Derricks, IBR approved for 1910.181(b)(2) and 1910.268(j)(4)(iv)(E) and (H).

1910.6(e)(22)

ANSI B31.1-55 Code for Pressure Piping, IBR approved for 1910.261(g)(18)(iii).

1910.6(e)(23)

ANSI B31.1-67, IBR approved for 1910.253(d)(1)(i)(A).

1910.6(e)(24)

ANSI B31.1a-63 Addenda to ANSI B31.1 (1955), IBR approved for 1910.261(g)(18)(iii).

..1910.6(e)(25)

1910.6(e)(25)

ANSI B31.1-67 and Addenda B31.1 (1969) Code for Pressure Piping, IBR approved for 1910.103(b)(1)(iii)(b); 1910.104(b)(5)(ii); 1910.218(d)(4) and (e)(1)(iv); and 1910.261(a)(3)(xiv) and (g)(18)(iii).

1910.6(e)(26)

ANSI B31.2-68 Fuel Gas Piping, IBR approved for 1910.261(g)(18)(iii).

1910.6(e)(27)

ANSI B31.3-66 Petroleum Refinery Piping, IBR approved for 1910.103(b)(3)(v)(b).

1910.6(e)(28)

ANSI B31.5-66 Addenda B31.5a (1968) Refrigeration Piping, IB approved for 1910.103(b)(3)(v)(b) and 1910.111(b)(7)(iii).

1910.6(e)(29)

ANSI B56.1-69 Safety Standard for Powered Industrial Trucks, IBR approved for 1910.178(a)(2) and (3) and 1910.261(a)(3)(xv), (b)(6), (m)(2), and (m)(5)(iii).

1910.6(e)(30)

ANSI B57.1-65 Compressed Gas Cylinder Valve Outlet and Inlet Connections, IBR approved for 1910.253(b)(1)(iii).

1910.6(e)(31)

ANSI B71.1-68 Safety Specifications for Power Lawn Mowers, IBR approved for 1910.243(e)(1)(i).

1910.6(e)(32)

ANSI B175.1-1991, Safety Requirements for Gasoline-Powered Chain Saws 1910.266(e)(2)(i).

..1910.6(e)(33)

1910.6(e)(33)

ANSI C1-71 National Electrical Code, IBR approved for 1910.66 Appendix D(c)(22)(i) and (vii).

1910.6(e)(34)

ANSI C33.2-56 Safety Standard for Transformer-Type Arc Welding Machines, IBR approved for 1910.254(b)(1).

1910.6(e)(35)

ANSI D8.1-67 Practices for Railroad Highway Grade Crossing Protection, IBR approved for 1910.265(c)(31)(i).

1910.6(e)(36)

ANSI H23.1-70 Seamless Copper Water Tube Specification, IBR approved for 1910.110(b)(8)(ii) and (13)(ii)(b)(1).

1910.6(e)(37)

ANSI H38.7-69 Specification for Aluminum Alloy Seamless Pipe and Seamless Extruded Tube, IBR approved for 1910.110(b)(8)(i).

1910.6(e)(38)

ANSI J6.4-71 Standard Specification for Rubber Insulating Blankets, IBR approved for 1910.268(f)(1) and (n)(11)(v).

1910.6(e)(39)

ANSI J6.6-71 Standard Specification for Rubber Insulating Gloves, IBR approved for 1910.268(f)(1) and (n)(11)(iv).

1910.6(e)(40)

ANSI K13.1-67 Identification of Gas Mask Canisters, IBR approved for 1910.261(a)(3)(xvi) and (h)(2)(iii).

1910.6(e)(41)

ANSI K61.1-60 Safety Requirements for the Storage and Handling of Anhydrous Ammonia, IBR approved for 1910.111(b)(11)(i).

..1910.6(e)(42)

1910.6(e)(42)

ANSI K61.1-66 Safety Requirements for the Storage and Handling of Anhydrous Ammonia, IBR approved for 1910.111(b)(11)(i).

1910.6(e)(43)

ANSI O1.1-54 (R 61) Safety Code for Woodworking Machinery, IBR approved for 1910.261(a)(3)(xvii), (e)(7), and (i)(2).

1910.6(e)(44)

ANSI S1.4-71 (R 76) Specification for Sound Level Meters, IBR approved for 1910.95 Appendixes D and I.

1910.6(e)(45)

ANSI S1.11-71 (R 76) Specification for Octave, Half-Octave and Third-Octave Band Filter Sets, IBR approved for 1910.95 Appendix D.

1910.6(e)(46)

ANSI S3.6-69 Specifications for Audiometers, IBR approved for 1910.95(h)(2) and (5)(ii) and Appendix D.

1910.6(e)(47)

ANSI Z4.1-68 Requirements for Sanitation in Places of Employment, IBR approved for 1910.261(a)(3)(xviii) and (g)(15)(vi).

1910.6(e)(48)

ANSI Z4.2-42 Standard Specifications for Drinking Fountains, IBR approved for 1910.142(c)(4).

1910.6(e)(49)

ANSI Z9.1-51 Safety Code for Ventilation and Operation of Open Surface Tanks, IBR approved for 1910.94(c)(5)(iii)(e) and 1910.261(a)(3)(xix), (g)(18)(v), and (h)(2)(i).

..1910.6(e)(50)

1910.6(e)(50)

ANSI Z9.1-71 Practices for Ventilation and Operation of Open-Surface Tanks, IBR approved for 1910.124(b)(4)(iv).

1910.6(e)(51)

ANSI Z9.2-60 Fundamentals Governing the Design and Operation of Local Exhaust Systems, IBR approved for 1910.94(a)(4)(i) introductory text, (a)(6) introductory text, (b)(3)(ix), (b)(4)(i) and (ii), (c)(3)(i) introductory text, (c)(5)(iii)(b), and (c)(7)(iv)(a); 1910.261(a)(3)(xx), (g)(1)(i) and (iii), and (h)(2)(ii).

1910.6(e)(52)

ANSI Z9.2-79 Fundamentals Governing the Design and Operation of Local Exhaust Systems, IBR approved for 1910.124(b)(4)(i).

1910.6(e)(53)

ANSI Z21.30-64 Requirements for Gas Appliances and Gas Piping Installations, IBR approved for 1910.265(c)(15).

1910.6(e)(54)

ANSI Z24.22-57 Method of Measurement of Real-Ear Attenuation of Ear Protectors at Threshold, IBR approved for 1910.261(a)(3)(xxii).

1910.6(e)(55)

ANSI Z33.1-61 Installation of Blower and Exhaust Systems for Dust, Stock, and Vapor Removal or Conveying, IBR approved for 1910.94(a)(4)(i); 1910.261(a)(3)(xxiii) and (f)(5); and 1910.265(c)(20)(i).

1910.6(e)(56)

ANSI Z33.1-66 Installation of Blower and Exhaust Systems for Dust, Stock, and Vapor Removal or Conveying, IBR approved for 1910.94(a)(2)(ii).

..1910.6(e)(57)

1910.6(e)(57)

ANSI Z35.1-68 Specifications for Accident Prevention Signs, IBR approved for 1910.261(a)(3)(xxiv) and (c)(16).

1910.6(e)(58)

ANSI Z41.1-67 Men's Safety Toe Footwear, IBR approved for 1910.94(a)(5)(v); 1910.136(b)(2) and 1910.261(i)(4).

1910.6(e)(59)

ANSI Z41-91, Personal Protection-Protective Footwear, IBR approved for 1910.136(b)(1).

1910.6(e)(60)

ANSI Z48.1-54 Method for Marking Portable Compressed Gas Containers to Identify the Material Contained, IBR approved for 1910.103(b)(1)(i)(c); 1910.110(b)(5)(iii); and 1910.253(b)(1)(ii).

1910.6(e)(61)

ANSI Z48.1-54 (R 70) Method for Marking Portable Compressed Gas Containers To Identify the Material Contained, IBR approved for 1910.111(e)(1) and 1910.134(d)(4).

1910.6(e)(62)

ANSI Z49.1-67 Safety in Welding and Cutting, IBR approved for 1910.252(c)(1)(iv)(A) and (B).

1910.6(e)(63)

ANSI Z53.1-67 Safety Color Code for Marking Physical Hazards and the Identification of Certain Equipment, IBR approved for 1910.97(a)(3)(ii); 1910.145(d)(2), (4), and (6).

..1910.6(e)(64)

1910.6(e)(64)

ANSI Z54.1-63 Safety Standard for Non-Medical X-Ray and Sealed Gamma Ray Sources, IBR approved for 1910.252(d)(1)(vii) and (2)(ii).

1910.6(e)(65)

ANSI Z87.1-68 Practice of Occupational and Educational Eye and Face Protection, IBR approved for 1910.133(b)(2); 1910.252(b)(2)(ii)(I); and 1910.261(a)(3)(xxv), (d)(1)(ii), (f)(5), (g)(10), (g)(15)(v), (g)(18)(ii), and (i)(4).

1910.6(e)(66)

ANSI Z87.1-89, Practice for Occupational and Educational Eye and Face Protection, IBR approved for 1910.133(b)(1).

1910.6(e)(67)

ANSI Z88.2-69 Practices for Respiratory Protection, IBR approved for 1910.94(c)(6)(iii)(a); 1910.134(c); and 1910.261(a)(3)(xxvi), (b)(2), (f)(5), (g)(15)(v), (h)(2)(iii) and (iv), and (i)(4).

1910.6(e)(68)

ANSI Z89.1-69 Safety Requirements for Industrial Head Protection, IBR approved for 1910.135(b)(2); and 1910.261(a)(3)(xxvii), (b)(2), (g)(15)(v), and (i)(4).

1910.6(e)(69)

ANSI Z89.1-86, Protective Headwear for Industrial Workers Requirements, IBR approved for 1910.135(b)(1).

1910.6(e)(70)

ANSI Z89.2-71 Safety Requirements for Industrial Protective Helmets for Electrical Workers, Class B, IBR approved for 1910.268(i)(1).

..1910.6(f)

1910.6(f)

The following material is available for purchase from the American Petroleum Institute (API), 1220 L Street NW, Washington DC 20005:

1910.6(f)(1)

API 12A (Sept. 1951) Specification for Oil Storage Tanks With Riveted Shells, 7th Ed., IBR approved for 1910.106(b)(1)(i)(a)(2).

1910.6(f)(2)

API 12B (May 1958) Specification for Bolted Production Tanks, 11th Ed., With Supplement No. 1, Mar. 1962, IBR approved for 1910.106(b)(1)(i)(a)(3).

1910.6(f)(3)

API 12D (Aug. 1957) Specification for Large Welded Production Tanks, 7th Ed., IBR approved for 1910.106(b)(1)(i)(a)(3).

1910.6(f)(4)

API 12F (Mar. 1961) Specification for Small Welded Production Tanks, 5th Ed., IBR approved for 1910.106(b)(1)(i)(a)(3).

1910.6(f)(5)

API 620, Fourth Ed. [1970] Including Appendix R, Recommended Rules for Design and Construction of Large Welded Low Pressure Storage Tanks, IBR approved for 1910.103(c)(1)(i)(a); 1910.106(b)(1)(iv)(b)(1); and 1910.111(d)(1)(ii) and (iii).

1910.6(f)(6)

API 650 (1966) Welded Steel Tanks for Oil Storage, 3rd Ed., IBR approved for 1910.106(b)(1)(iii)(a)(2).

..1910.6(f)(7)

1910.6(f)(7)

API 1104 (1968) Standard for Welding Pipelines and Related Facilities, IBR approved for 1910.252(d)(1)(v).

1910.6(f)(8)

API 2000 (1968) Venting Atmospheric and Low Pressure Storage Tanks, IBR approved for 1910.106(b)(2)(iv)(b)(1).

1910.6(f)(9)

API 2201 (1963) Welding or Hot Tapping on Equipment Containing Flammables, IBR approved for 1910.252(d)(1)(vi).

1910.6(g)

The following material is available for purchase from the American Society of Mechanical Engineers (ASME), United Engineering Center, 345 East 47th Street, New York, NY 10017:

1910.6(g)(1)

ASME Boiler and Pressure Vessel Code, VIII, 1949, 1950, 1952, 1956, 1959, and 1962 Ed., IBR approved for 1910.110(b)(10)(iii) (Table H-26), (d)(2) (Table H-31); (e)(3)(i) (Table H-32), (h)(2) (Table H-34); and 1910.111(b)(2)(vi);

1910.6(g)(2)

ASME Code for Pressure Vessels, 1968 Ed., IBR approved for 1910.106(i)(3)(i); 1910.110(g)(2)(iii)(b)(2); and 1910.217(b)(12);

..1910.6(g)(3)

1910.6(g)(3)

ASME Boiler and Pressure Vessel Code, VIII, 1968, IBR approved for 1910.103; 1910.104(b)(4)(ii); 1910.106(b)(1)(iv)(b)(2) and (i)(3)(ii); 1910.107; 1910.110(b)(11)(i)(b) and (iii)(a)(1); 1910.111(b)(2)(i), (ii), and (iv); and 1910.169(a)(2)(i) and (ii);

1910.6(g)(4)

ASME Boiler and Pressure Vessel Code, VIII, Paragraph UG-84, 1968, IBR approved for 1910.104(b)(4)(ii) and (b)(5)(iii);

1910.6(g)(5)

ASME Boiler and Pressure Vessel Code, VIII, Unfired Pressure Vessels, Including Addenda (1969), IBR approved for 1910.261; 1910.262; 1910.263(i)(24)(ii);

1910.6(g)(6)

Code for Unfired Pressure Vessels for Petroleum Liquids and Gases of the API and the ASME, 1951 Ed., IBR approved for 1910.110(b)(3)(iii); and

1910.6(g)(7)

ASME B56.6-1992 (with addenda), Safety Standard for Rough Terrain Forklift Trucks, IBR approved for 1910.266(f)(4).

1910.6(h)

The following material is available for purchase from the American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103:

1910.6(h)(1)

ASTM A 47-68 Malleable Iron Castings, IBR approved for 1910.111(b)(7)(vi).

..1910.6(h)(2)

1910.6(h)(2)

ASTM A 53-69 Welded and Seamless Steel Pipe, IBR approved for 1910.110(b)(8)(i)(a) and (b) and 910.111(b)(7)(iv).

1910.6(h)(3)

ASTM A 126-66 Gray Iron Casting for Valves, Flanges and Pipe Fitting, IBR approved for 1910.111(b)(7)(vi).

1910.6(h)(4)

ASTM A 391-65 (ANSI G61.1-1968) Alloy Steel Chain, IBR approved for 1910.184(e)(4).

1910.6(h)(5)

ASTM A 395-68 Ductile Iron for Use at Elevated Temperatures, IBR approved for 1910.111(b)(7)(vi).

1910.6(h)(6)

ASTM B 88-69 Seamless Copper Water Tube, IBR approved for 1910.110(b)(8)(i)(a) and (13)(ii)(b)(1).

1910.6(h)(7)

ASTM B 88-66A Seamless Copper Water Tube, IBR approved for 1910.252(d)(1)(i)(A)(2).

1910.6(h)(8)

ASTM B 117-64 Salt Spray (Fog) Test, IBR approved for 1910.268(g)(2)(i)(A).

1910.6(h)(9)

ASTM B 210-68 Aluminum-Alloy Drawn Seamless Tubes, IBR approved for 1910.110(b)(8)(ii).

1910.6(h)(10)

ASTM B 241-69, IBR approved for 1910.110(b)(8)(i) introductory text.

..1910.6(h)(11)

1910.6(h)(11)

ASTM D 5-65 Test for Penetration by Bituminous Materials, IBR approved for 1910.106(a)(17).

1910.6(h)(12)

ASTM D 56-70 Test for Flash Point by Tag Closed Tester, IBR approved for 1910.106(a)(14)(i).

1910.6(h)(13)

ASTM D 86-62 Test for Distillation of Petroleum Products, IBR approved for 1910.106(a)(5) and 1910.119(b) "Boiling point."

1910.6(h)(14)

ASTM D 88-56 Test for Saybolt Viscosity, IBR approved for 1910.106(a)(37).

1910.6(h)(15)

ASTM D 93-71 Test for Flash Point by Pensky Martens, IBR approved for 1910.106(a)(14)(ii).

1910.6(h)(16)

ASTM D 323-68, IBR approved for 1910.106(a)(30).

1910.6(h)(17)

ASTM D 445-65 Test for Viscosity of Transparent and Opaque Liquids, IBR approved for 1910.106(a)(37).

1910.6(h)(18)

ASTM D 1692-68 Test for Flammability of Plastic Sheeting and Cellular Plastics, IBR approved for 1910.103(c)(1)(v)(d).

1910.6(h)(19)

ASTM D 2161-66 Conversion Tables For SUS, IBR approved for 1910.106(a)(37).

..1910.6(i)

1910.6(i)

The following material is available for purchase from the American Welding Society (AWS), 550 NW, LeJeune Road, P.O. Box 351040, Miami FL 33135:

1910.6(i)(1)

AWS A3.0 (1969) Terms and Definitions, IBR approved for 1910.251(c).

1910.6(i)(2)

AWS A6.1 (1966) Recommended Safe Practices for Gas Shielded Arc Welding, IBR approved for 1910.254(d)(1).

1910.6(i)(3)

AWS B3.0-41 Standard Qualification Procedure, IBR approved for 1910.67(c)(5)(i).

1910.6(i)(4)

AWS D1.0-1966 Code for Welding in Building Construction, IBR approved for 1910.27(b)(6).

1910.6(i)(5)

AWS D2.0-69 Specifications for Welding Highway and Railway Bridges, IBR approved for 1910.67(c)(5)(iv).

1910.6(i)(6)

AWS D8.4-61 Recommended Practices for Automotive Welding Design, IBR approved for 1910.67(c)(5)(ii).

1910.6(i)(7)

AWS D10.9-69 Standard Qualification of Welding Procedures and Welders for Piping and Tubing, IBR approved for 1910.67(c)(5)(iii).

..1910.6(j)

1910.6(j)

The following material is available for purchase from the Department of Commerce:

1910.6(j)(1)

Commercial Standard, CS 202-56 (1961) "Industrial Lifts and Hinged Loading Ramps," IBR approved for 1910.30(a)(3).

1910.6(j)(2)

Publication "Model Performance Criteria for Structural Fire Fighters' Helmets," IBR approved for 1910.156(e)(5)(i).

1910.6(k)

The following material is available for purchase from the Compressed Gas Association (CGA), 1235 Jefferson Davis Highway, Arlington, VA 22202:

1910.6(k)(1)

CGA C-6 (1968) Standards for Visual Inspection of Compressed Gas Cylinders, IBR approved for 1910.101(a).

1910.6(k)(2)

CGA C-8 (1962) Standard for Requalification of ICC-3HT Cylinders, IBR approved for 1910.101(a).

1910.6(k)(3)

CGA G-1 (1966) Acetylene, IBR approved for 1910.102(a).

1910.6(k)(4)

CGA G-1.3 (1959) Acetylene Transmission for Chemical Synthesis, IBR approved for 1910.102(b).

1910.6(k)(5)

CGA G-1.4 (1966) Standard for Acetylene Cylinder Charging Plants, IBR approved for 1910.102(b).

..1910.6(k)(6)

1910.6(k)(6)

CGA G-7.1 (1966) Commodity Specification, IBR approved for 1910.134(d)(1).

1910.6(k)(7)

CGA G-8.1 (1964) Standard for the Installation of Nitrous Oxide Systems at Consumer Sites, IBR approved for 1910.105.

1910.6(k)(8)

CGA P-1 (1965) Safe Handling of Compressed Gases, IBR approved for 1910.101(b).

1910.6(k)(9)

CGA P-3 (1963) Specifications, Properties, and Recommendations for Packaging, Transportation, Storage and Use of Ammonium Nitrate, IBR approved for 1910.109(i)(1)(ii)(b).

1910.6(k)(10)

CGA S-1.1 (1963) and 1965 Addenda. Safety Release Device Standards--Cylinders for Compressed Gases, IBR approved for 1910.101(c); 1910.103(c)(1)(iv)(a)(2).

1910.6(k)(11)

CGA S-1.2 (1963) Safety Release Device Standards, Cargo and Portable Tanks for Compressed Gases, IBR approved for 1910.101(c); 1910.103(c)(1)(iv)(a)(2).

1910.6(k)(12)

CGA S-1.3 (1959) Safety Release Device Standards-Compressed Gas Storage Containers, IBR approved for 1910.103(c)(1)(iv)(a)(2); 1910.104(b)(6)(iii); and 1910.111(d)(4)(ii)(b).

..1910.6(k)(13)

1910.6(k)(13)

CGA 1957 Standard Hose Connection Standard, IBR approved for 1910.253(e)(4)(v) and (5)(iii).

1910.6(k)(14)

CGA and RMA (Rubber Manufacturer's Association) Specification for Rubber Welding Hose (1958), IBR approved for 1910.253(e)(5)(i).

1910.6(k)(15)

CGA 1958 Regulator Connection Standard, IBR approved for 1910.253(e)(4)(iv) and (6).

1910.6(l)

The following material is available for purchase from the Crane Manufacturer's Association of America, Inc. (CMAA), 1 Thomas Circle NW, Washington DC 20005:

1910.6(l)(1)

CMAA Specification 1B61, Specifications for Electric Overhead Traveling Cranes, IBR approved for 1910.179(b)(6)(i).

1910.6(l)(2)

[Reserved].

1910.6(m)

The following material is available for purchase from the General Services Administration:

1910.6(m)(1)

GSA Pub. GG-B-0067b, Air Compressed for Breathing Purposes, or Interim Federal Specifications, Apr. 1965, IBR approved for 1910.134(d)(4).

..1910.6(m)(2)

1910.6(m)(2)

[Reserved]

1910.6(n)

The following material is available for purchase from the Department of Health and Human Services:

1910.6(n)(1)

Publication No. 76-120 (1975), List of Personal Hearing Protectors and Attenuation Data, IBR approved for 1910.95 App. B.

1910.6(n)(2)

[Reserved]

1910.6(o)

The following material is available for purchase from the Institute of Makers of Explosives (IME), 420 Lexington Avenue, New York, NY 10017:

1910.6(o)(1)

IME Pamphlet No. 17, 1960, Safety in the Handling and Use of Explosives, IBR approved for 1910.261(a)(4)(iii) and (c)(14)(ii).

1910.6(o)(2)

[Reserved]

1910.6(p)

The following material is available for purchase from the National Electrical Manufacturer's Association (NEMA):

..1910.6(p)(1)

1910.6(p)(1)

NEMA EW-1 (1962) Requirements for Electric Arc Welding Apparatus, IBR approved for 1910.254(b)(1).

1910.6(p)(2)

[Reserved]

1910.6(q)

The following material is available for purchase from the National Fire Protection Association (NFPA), 11 Tracy Drive, Avon, MA 02322:

1910.6(q)(1)

NFPA 30 (1969) Flammable and Combustible Liquids Code, IBR approved for 1910.178(f)(1).

1910.6(q)(2)

NFPA 32-1970 Standard for Dry Cleaning Plants, IBR approved for 1910.106(j)(6)(i).

1910.6(q)(3)

NFPA 33-1969 Standard for Spray Finishing Using Flammable and Combustible Material, IBR approved for 1910.94(c)(1)(ii), (2), (3)(i) and (iii), and (5).

1910.6(q)(4)

NFPA 34-1966 Standard for Dip Tanks Containing Flammable or Combustible Liquids, IBR approved for 1910.124(b)(4)(iv).

1910.6(q)(5)

NFPA 34-1995 Standard for Dip Tanks Containing Flammable or Combustible Liquids, IBR approved for 1910.124(b)(4)(ii).

1910.6(q)(6)

NFPA 35-1970 Standard for the Manufacture of Organic Coatings, IBR approved for Sec. 1910.106(j)(6)(ii).

..1910.6(q)(7)

1910.6(q)(7)

NFPA 36-1967 Standard for Solvent Extraction Plants, IBR approved for 1910.106(j)(6)(iii).

1910.6(q)(8)

NFPA 37-1970 Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines, IBR approved for 1910.106(j)(6)(iv) and 1910.110(b)(20)(iv)(c) and (e)(11).

1910.6(q)(9)

NFPA 51B-1962 Standard for Fire Protection in Use of Cutting and Welding Processes, IBR approved for 1910.252(a)(1) introductory text.

1910.6(q)(10)

NFPA 54-1969 Standard for the Installation of Gas Appliances and Gas Piping, IBR approved for 1910.110(b)(20)(iv)(a).

1910.6(q)(11)

NFPA 54A-1969 Standard for the Installation of Gas Piping and Gas Equipment on Industrial Premises and Certain Other Premises, IBR approved for 1910.110(b)(20)(iv)(b).

1910.6(q)(12)

NFPA 58-1969 Standard for the Storage and Handling of Liquefied Petroleum Gases (ANSI Z106.1-1970), IBR approved for 1910.110(b)(3)(iv) and (i)(3)(i) and (ii); and 1910.178(f)(2).

1910.6(q)(13)

NFPA 59-1968 Standard for the Storage and Handling of Liquefied Petroleum Gases at Utility Gas Plants, IBR approved for 1910.110(b)(3)(iv) and (i)(2)(iv).

..1910.6(q)(13)

1910.6(q)(14)

NFPA 62-1967 Standard for the Prevention of Dust Explosions in the Production, Packaging, and Handling of Pulverized Sugar and Cocoa, IBR approved for 1910.263(k)(2)(i).

1910.6(q)(15)

NFPA 68-1954 Guide for Explosion Venting, IBR approved for 1910.94(a)(2)(iii).

1910.6(q)(16)

NFPA 70-1971 National Electrical Code, IBR approved for 1910.66 App. D(c)(2).

1910.6(q)(17)

NFPA 78-1968 Lightning Protection Code, IBR approved for 1910.109(i)(6)(ii).

1910.6(q)(18)

NFPA 80-1968 Standard for Fire Doors and Windows, IBR approved for 1910.106(d)(4)(i).

1910.6(q)(19)

NFPA 80-1970 Standard for the Installation of Fire Doors and Windows, IBR approved for 1910.253(f)(6)(i)(I).

1910.6(q)(20)

NFPA 86A-1969 Standard for Oven and Furnaces Design, Location and Equipment, IBR approved for 1910.107(j)(1) and (l)(3) and 1910.108(b)(2) and (d)(2).

1910.6(q)(21)

NFPA 91-1961 Standard for the Installation of Blower and Exhaust Systems for Dust, Stock, and Vapor Removal or Conveying (ANSI Z33.1-61), IBR approved for 1910.107(d)(1).

..1910.6(q)(21)

1910.6(q)(22)

NFPA 91-1969 Standards for Blower and Exhaust Systems, IBR approved for 1910.108(b)(1).

1910.6(q)(23)

NFPA 96-1970 Standard for the Installation of Equipment for the Removal of Smoke and Grease Laden Vapors from Commercial Cooking Equipment, IBR approved for 1910.110(b)(20)(iv)(d).

1910.6(q)(24)

NFPA 101-1970 Code for Life Safety From Fire in Buildings and Structures, IBR approved for 1910.261(a)(4)(ii).

1910.6(q)(25)

NFPA 203M-1970 Manual on Roof Coverings, IBR approved for 1910.109(i)(1)(iii)(c).

1910.6(q)(26)

NFPA 251-1969 Standard Methods of Fire Tests of Building Construction and Materials, IBR approved for 1910.106(d)(3)(ii) introductory text and (d)(4)(i).

1910.6(q)(27)

NFPA 302-1968 Fire Protection Standard for Motor-Craft (Pleasure and Commercial), IBR approved for 1910.265(d)(2)(iv) introductory text.

1910.6(q)(28)

NFPA 385-1966 Recommended Regulatory Standard for Tank Vehicles for Flammable and Combustible Liquids, IBR approved for 1910.106(g)(1)(i)(e)(1).

..1910.6(q)(28)

1910.6(q)(29)

NFPA 496-1967 Standard for Purged Enclosures for Electrical Equipment in Hazardous Locations, IBR approved for 1910.103(c)(1)(ix)(e)(1).

1910.6(q)(30)

NFPA 505-1969 Standard for Type Designations, Areas of Use, Maintenance, and Operation of Powered Industrial Trucks, IBR approved for 1910.110(e)(2)(iv).

1910.6(q)(31)

NFPA 566-1965 Standard for the Installation of Bulk Oxygen Systems at Consumer Sites, IBR approved for 1910.253(b)(4)(iv) and (c)(2)(v).

1910.6(q)(32)

NFPA 656-1959 Code for the Prevention of Dust Ignition in Spice Grinding Plants, IBR approved for 1910.263(k)(2)(i).

1910.6(q)(33)

NFPA 1971-1975 Protective Clothing for Structural Fire Fighting, IBR approved for 1910.156(e)(3)(ii) introductory text.

1910.6(r)

The following material is available for purchase from the National Food Plant Institute, 1700 K St. NW., Washington, DC 20006:

1910.6(r)(1)

Definition and Test Procedures for Ammonium Nitrate Fertilizer (Nov. 1964), IBR approved for 1910.109 Table H-22, Footnote 3.

1910.6(r)(2)

[Reserved]

..1910.6(s)

1910.6(s)

The following material is available for purchase from the National Institute for Occupational Safety and Health (NIOSH):

1910.6(s)(1)

Registry of Toxic Effects of Chemical Substances, 1978, IBR approved for 1910.20(c)(13)(i) and Appendix B.

1910.6(s)(2)

Development of Criteria for Fire Fighters Gloves; Vol. II, Part II; Test Methods, 1976, IBR approved for 1910.156(e)(4)(i) introductory text.

1910.6(s)(3)

NIOSH Recommendations for Occupational Safety and Health Standards (Sept. 1987), IBR approved for 1910.120 PEL definition.

1910.6(t)

The following material is available for purchase from the Public Health Service:

1910.6(t)(1)

U.S. Pharmacopeia, IBR approved for 1910.134(d)(1).

1910.6(t)(2)

Publication No. 934 (1962), Food Service Sanitation Ordinance and Code, Part V of the Food Service Sanitation Manual, IBR approved for 1910.142(i)(1).

1910.6(u)

The following material is available for purchase from the Society of Automotive Engineers (SAE), 485 Lexington Avenue, New York, NY 10017:

..1910.6(u)(1)

1910.6(u)(1)

SAE J185, June 1988, Recommended Practice for Access Systems for Off-Road Machines, IBR approved for 1910.266(f)(5)(i).

1910.6(u)(2)

SAE J231, January 1981, Minimum Performance Criteria for Falling Object Protective Structure (FOPS), IBR approved for 1910.266(f)(3)(ii).

1910.6(u)(3)

SAE J386, June 1985, Operator Restraint Systems for Off-Road Work Machines, IBR approved for 1910.266(d)(3)(iv).

1910.6(u)(4)

SAE J397, April 1988, Deflection Limiting Volume-ROPS/FOPS Laboratory Evaluation, IBR approved for 1910.266(f)(3)(iv).

1910.6(u)(5)

SAE 765 (1961) SAE Recommended Practice: Crane Loading Stability Test Code, IBR approved for 1910.180(c)(1)(iii) and (e)(2)(iii)(a).

1910.6(u)(6)

SAE J1040, April 1988, Performance Criteria for Rollover Protective Structures (ROPS) for Construction, Earthmoving, Forestry and Mining Machines, IBR approved for 1910.266(f)(3)(ii).

1910.6(v)

The following material is available for purchase from the Fertilizer Institute, 1015 18th Street NW, Washington, DC 20036:

..1910.6(v)(1)

1910.6(v)(1)

Standard M-1 (1953, 1955, 1957, 1960, 1961, 1963, 1965, 1966, 1967, 1968), Superseded by ANSI K61.1-1972, IBR approved for 1910.111(b)(1)(i) and (iii).

1910.6(v)(2)

[Reserved]

1910.6(w)

The following material is available for purchase from Underwriters Laboratories (UL), 207 East Ohio Street, Chicago, IL 60611:

1910.6(w)(1)

UL 58-61 Steel Underground Tanks for Flammable and Combustible Liquids, 5th Ed., IBR approved for 1910.106(b)(1)(iii)(a)(1).

1910.6(w)(2)

UL 80-63 Steel Inside Tanks for Oil-Burner Fuel, IBR approved for 1910.106(b)(1)(iii)(a)(1).

1910.6(w)(3)

UL 142-68 Steel Above Ground Tanks for Flammable and Combustible Liquids, IBR approved for 1910.106(b)(1)(iii)(a)(1).

[39 FR 23502, June 27, 1974, as amended at 49 FR 5321, Feb. 10, 1984; 61 FR 9227, March 7, 1996; 64 FR 13908, March 23, 1999]

Act now! It is essential that you inquire about your case as soon as possible. Litigation may be the only way to receive the damages to which you may be entitled, such as medical and health care bills, lost or diminished wages, and financial compensation to family in the case of death. Your individual state's law may limit your time to bring a legal claim to protect your rights. You need to have your construction accidents claim evaluated immediately!

Click To Talk To Us Online

see also:

Standards Petitions FREE construction accidents OSHA information: Petitions for the issuance, amendment, or repeal of a standard.
construction accidents info: General, Petitions for the issuance, amendment, or repeal of a standard.

Applicability of standards FREE construction accidents OSHA information: Applicability of standards.
construction accidents info: General, Applicability of standards.

Authority for 1910 Subpart A FREE construction accidents OSHA information: Authority for 1910 Subpart A
construction accidents info: General, Authority for 1910 Subpart A